Harding Series with 1" Thick Phenolic Resin Top and Square Cut Edge

As low as $474 Regular Price $474

Model

Skip to the beginning of the images gallery

Meets ANSI/BIFMA, DIN and GSA Structural Standards.
See Chemical, Stain, Microbial and Moisture Resistance.
20,000# Capacity Apron.
14-gauge Strong Cold Rolled Steel.
3" Square Legs.
2" x 3" Rectangular Frame Tube.
One Bolt Per Leg Assembly.
Factory Assembly Available.
Available 24”, 30”, 36”, 48” Wide or Custom.

Harding Series heavy duty benches come standard with adjustable height glides. Bolt down plates are available upon request.

Ease of Assembly

Harding Series Bench Assembly.

We are the Only National Workbench Manufacturer that Welds the Frame Together and Assembles it to the Top.

1. Place your new workbench on top of a table with the cardboard seam facing up. Open the carton. Do not remove the cardboard yet. If you ordered drawers or CPU holders, assemble them before the legs. (Go to their individual web site pages for instructions if needed. (benchdepot.com)

2. Position the legs. If you have a lot of benches to do, we recommend two man teams. If you have Static Control benches, make certain the wrist strap jack is on the front side of the leg.

3. Insert two screws with lock washers into each leg.

4. Tighten until lock washer is flat. It doesn't have to be tighter than that.

5. You're done. Turn it over. Its easier and safer with two men. Toss out the cardboard.

Unconditional Warranty

PRINT

Workbench Warranty

BenchPro™ has been producing the nation's strongest, longest lasting ergonomic workbenches since 1987. We are so sure our products will perform properly, we offer the following warranty:

BenchPro™ benches, options and accessories are warranted to the original purchaser for 25 - years. This includes every component and every function.

Exceptions:

Eisenhower series are warranted for ten years.

Workbenches used in multiple shift operations shall have the warranty prorated accordingly.

Hydraulic bench lift - system components are warranted for ten - years.

All lighting products are warranted for ten - years.

BenchPro™ will either refund the entire purchase price including freight and tax (if any) or replace the product or component that is defective, and pay for the freight.

Product Returns:

As we make all products from base materials, we charge a "restocking charge" on products returned if for no fault of ours. We also charge a restocking charge for products ordered but cancelled after the product is built. We do not accept used product back. If returned product is due to our fault, we credit the full cost, and freight.

Restocking charge schedule:

A. All Workbenches and Accessories in standard sizes and colors will be charged 25%.
B. Any bench in a custom size or color will be charged a 50% restocking charge, as we will have a difficult time reselling them.
C. Chemical Resistant tops will be charged an additional 10% restocking charge, above those listed above.
D. Custom and non-catalogue items are non-returnable.
E. No product shall be returned after 90 days.

No return of defective product is ever required. (We may ask for an electronic photo in cases where we have not seen the problem before).

From the lawyers: In no case shall BenchPro™, its distributors, employees, related divisions, and other entities be responsible for any direct, consequential or indirect damage caused by the use, inability to use, or incorrect use of our products. Our liability shall be limited to replacement of product or a full refund.

Due Diligence: Please, if a chair or workbench is found to be defective in a way that could lead to an accident, take it out of service and tag it as dangerous until replacements or replacement parts are received and assembled. Dangerous products should not be put into open waste disposal systems until they have been made unusable, so that no third party can reclaim them and be injured.

Recommended Height

What is the best work surface height for me?

You can order your benches at any work surface height without incurring additional cost, or select the lowest height you believe useful and add either our optional adjustable legs, our electric lift system or our crank-up system.

We have seen orders for almost every work surface height. Some Customers want to sit down and work, others want to stand. Here are some thoughts that may be of assistance:

1. Desks are 30" high.

2. Desk chairs usually have a seat cushion height adjustability range of around 17" to 22".

3. Work surfaces should never be more than 9" higher than the top of the chair range. Conclusion: If you need a work surface higher than 31", you will need a taller chair.

4. Taller chairs usually have a foot ring and a wider base. (Adjustable foot rings are critical as employees come in all sizes too.)

5. Our taller chairs have a seat cushion height adjustability range of 22" to 32". (Some brands have ranges of only 5" or 8".)

6. We do not recommend chairs be used at benches with work surfaces of 37" and higher, as some employees will attempt to "climb" the chair, and could be injured when the chair rolls or tips.

View All Accessories

Popular Accessories

View All Accessories
	Drawers These fully-welded drawers hold up 100 lbs.
	Shelves Choose from upright-mounted, riser or under-shelves.
	Lights Add fluorescent or LED lights above your workbench.
	Uprights Add shelves lights or accessories above your workbench.
	Power Strips Add UL listed power strips to your workbench.
	Bin Rails Add convenient bin access to your workbench.
	Casters Make your workbench mobile with these non-marring casters.
	Articulating Accessories Choose from Monitor, Bin Box, Document and Tool Holders.