Grant Series with 3/4" Thick Phenolic Resin Top.

Meet ANSI, BIFMA, DIN and GSA Structural Standards.
See Chemical Resist, Stain and Physical Tests.
2,000 Lbs. Capacity.
16-gauge and 18-gauge Strong Cold Rolled Steel.
Factory Assembly Available.
Available 24”, 30”, 36” Wide or Custom.

$1,000

Model

GSZ

Skip to the end of the images gallery

Skip to the beginning of the images gallery

Ease of Assembly

Grant Series Bench Assembly.

BenchPro™ Grant Series workbenches are fastened together using special "T-Head" threaded fasteners. These fasteners are inserted into the slots of the upright end panels, and are turned 1/4 turn to lock into the channel. Then the Nylock nuts are tightened up to secure the assembly.

BenchPro™ Uprights have slots which accept the T-Head fasteners.

1. Position the work surface upside down on a small table or bench. Turn the heads on the fasteners so the heads are positioned vertically.

2. Determine which side of an end leg panel is to be connected to the work surface. Position the end panel with the horizontal feet facing up. Slide the T-Heads into the slot, turn the nylock fastener until slightly tight.

3. Slide the legs to the desired work surface height.

4. Tighten the Nylock nuts . the desired work surface height while observing the height marking tape.

5. Position the modesty panel all the way down against the work surface bottom.

6. Tighten the Nylock fasteners.

7. Using an electric drill, fasten the top of the modesty panel to the bottom of the work surface.

8. Turn the workbench over.

9. Install the end panel top caps using the two fasteners provided.

Unconditional Warranty

PRINT

Workbench Warranty

BenchPro™ has been producing the nation's strongest, longest lasting ergonomic workbenches since 1987. We are so sure our products will perform properly, we offer the following warranty:

BenchPro™ benches, options and accessories are warranted to the original purchaser for 25 - years. This includes every component and every function.

Exceptions:

Eisenhower series are warranted for ten years.

Workbenches used in multiple shift operations shall have the warranty prorated accordingly.

Hydraulic bench lift - system components are warranted for ten - years.

All lighting products are warranted for ten - years.

BenchPro™ will either refund the entire purchase price including freight and tax (if any) or replace the product or component that is defective, and pay for the freight.

Product Returns:

As we make all products from base materials, we charge a "restocking charge" on products returned if for no fault of ours. We also charge a restocking charge for products ordered but cancelled after the product is built. We do not accept used product back. If returned product is due to our fault, we credit the full cost, and freight.

Restocking charge schedule:

A. All Workbenches and Accessories in standard sizes and colors will be charged 25%.
B. Any bench in a custom size or color will be charged a 50% restocking charge, as we will have a difficult time reselling them.
C. Chemical Resistant tops will be charged an additional 10% restocking charge, above those listed above.
D. Custom and non-catalogue items are non-returnable.
E. No product shall be returned after 90 days.

No return of defective product is ever required. (We may ask for an electronic photo in cases where we have not seen the problem before).

From the lawyers: In no case shall BenchPro™, its distributors, employees, related divisions, and other entities be responsible for any direct, consequential or indirect damage caused by the use, inability to use, or incorrect use of our products. Our liability shall be limited to replacement of product or a full refund.

Due Diligence: Please, if a chair or workbench is found to be defective in a way that could lead to an accident, take it out of service and tag it as dangerous until replacements or replacement parts are received and assembled. Dangerous products should not be put into open waste disposal systems until they have been made unusable, so that no third party can reclaim them and be injured.

Recommended Height

What is the best work surface height for me?

You can order your benches at any work surface height without incurring additional cost, or select the lowest height you believe useful and add either our optional adjustable legs, our electric lift system or our crank-up system.

We have seen orders for almost every work surface height. Some Customers want to sit down and work, others want to stand. Here are some thoughts that may be of assistance:

1. Desks are 30" high.

2. Desk chairs usually have a seat cushion height adjustability range of around 17" to 22".

3. Work surfaces should never be more than 9" higher than the top of the chair range. Conclusion: If you need a work surface higher than 31", you will need a taller chair.

4. Taller chairs usually have a foot ring and a wider base. (Adjustable foot rings are critical as employees come in all sizes too.)

5. Our taller chairs have a seat cushion height adjustability range of 22" to 32". (Some brands have ranges of only 5" or 8".)

6. We do not recommend chairs be used at benches with work surfaces of 37" and higher, as some employees will attempt to "climb" the chair, and could be injured when the chair rolls or tips.