Meet ANSI, BIFMA, DIN and GSA Structural Standards.
2,000 Lbs. Capacity.
16-gauge and 18-gauge Strong Cold Rolled Steel.
Factory Assembly Available.
1.2" Thick Top.
Pass ESD Association Standards.
Available 24”, 30”, 36”, 48” Wide or Custom.

Workbench Warranty

BenchPro™ has been producing the nation's strongest, longest lasting ergonomic workbenches since 1987. We are so sure our products will perform properly, we offer the following warranty:

BenchPro™ benches, options and accessories are warranted to the original purchaser for 25 - years. This includes every component and every function.

Exceptions:

Eisenhower series are warranted for ten years.

Workbenches used in multiple shift operations shall have the warranty prorated accordingly.

Hydraulic bench lift - system components are warranted for ten - years.

All lighting products are warranted for ten - years.

BenchPro™ will either refund the entire purchase price including freight and tax (if any) or replace the product or component that is defective, and pay for the freight.

Product Returns:

As we make all products from base materials, we charge a "restocking charge" on products returned if for no fault of ours. We also charge a restocking charge for products ordered but cancelled after the product is built. We do not accept used product back. If returned product is due to our fault, we credit the full cost, and freight.

Restocking charge schedule:

A. All Workbenches and Accessories in standard sizes and colors will be charged 25%.
B. Any bench in a custom size or color will be charged a 50% restocking charge, as we will have a difficult time reselling them.
C. Chemical Resistant tops will be charged an additional 10% restocking charge, above those listed above.
D. Custom and non-catalogue items are non-returnable.
E. No product shall be returned after 90 days.

No return of defective product is ever required. (We may ask for an electronic photo in cases where we have not seen the problem before).

From the lawyers: In no case shall BenchPro™, its distributors, employees, related divisions, and other entities be responsible for any direct, consequential or indirect damage caused by the use, inability to use, or incorrect use of our products. Our liability shall be limited to replacement of product or a full refund.

Due Diligence: Please, if a chair or workbench is found to be defective in a way that could lead to an accident, take it out of service and tag it as dangerous until replacements or replacement parts are received and assembled. Dangerous products should not be put into open waste disposal systems until they have been made unusable, so that no third party can reclaim them and be injured.

Ease of Assembly

Jefferson Series Bench Assembly.

We are the Only National Workbench Manufacturer that Welds the Frame Together and Assembles it to the Top.

1. Place packaged bench on top of elevated surface with seams on top.

2. Cut tape and fold down flaps. Do not remove cardboard.

Note 1. We package the legs with the top on longer tables. Smaller tables will have the leg sections in a a second box.

2.1. You will notice that there are only four parts to assemble. We have factory assembled the tops to the frame, inserted all other fasteners so there is no package of assorted fasteners to sort out and count.

This allows for easy assembly while reducing freight costs by about 65%.

Note: How the preassembled bolts have "T-Shaped" heads. Position these heads as shown in the photo below.

3. The preassembled leg sections each have a hinged door. Hold the door up while you lower the leg section over the top bracket so the fasteners slide into the inside slot on the solid aluminum leg extrusions.

4. Use the enclosed wrench to tighten the exposed nylock fasteners. The fasteners will first turn 1/4 turn and lock into the channel slots. Continue tightening the nuts until tight without allowing them to turn backwards.

5. Close the hinged flap.

Secure the door with one chrome head self drilling screw.

6. Push the legs apart slightly. Insert the "T-Head" screws preassembled into the modesty panel into the back slots so the flat side of the panel face away from the operator.

Slide the panel surely to the underside of the top.

Tighten the nuts.

7. Using an electric screwdriver, insert the remaining fasteners to attach the modesty panel to the bottom of the top.

8. Have two people lift the table and place it on the floor. Dispose of the cardboard.

Industrial Workbenches & Chairs

Jefferson Series with LisStat™ ESD Static Control Laminate Top and Round Front Edge

Workbench Warranty

Jefferson Series Bench Assembly.