Lincoln Fabric ESD Tall Chairs

As low as $268 Regular Price $268

Model

LNT-DF1A

Skip to the beginning of the images gallery

For perfect continuity,ESD chairs must have chrome plated back bars and gas lift tubes, plus special conductive oil in the lift tubes. Check ESD chairs with a surface resistance meter that applies 100 volts. This will only measure the dissipative range of the fabric. Now measure from any point on the fabric on either cushion to the drag chain or ESD caster. It’s easy if you have some thin metal. Just put it under a caster or the chain.

ANSI/BIFMA requires a rating of ten to the ninth or lower, but not lower than ten to the fifth.

Specifications

Foam Construction: 2.5” Thick Quadruple Density urethane foam. The top layer is Memory Foam for exceptional comfort, under that is soft foam maximize comfort for lighter weight people, then Medium Density followed by extra firm foam for the heavier people.

Height 1 Lever:

Nylon Base: 19" to 27".
Aluminum Base: 18" to 26".
Chrome Base: 20"to 28".

Height 3 Lever:

Nylon Base: 19" to 27".
Aluminum Base: 20" to 28".
Chrome Base: 22"to 30".

Seat: 19" Wide, 17" Deep. Waterfall Front. Fully Ergonomic.
Back: 13.5" High. Comfortable Lumbar Support.
Base: 5 Leg.
Weight Capacity: 450#.

Footring Diameter: 18".

Fabric: 10⁵- 10⁶Ω/sq.

Complies ANSI/ESD ST12.1-2006 standards.

Fabrics: Marquesa Lana Polyolefin Fabrics.

Fabric Durability: Estimated 25 years use.

Seat Pan: Seven Ply Individually Formed Hardwood Plywood.

Structural Standards: Meets All Requirements of ANSI/BIFMA, DIN, GSA and ESDA.

Fire Standard: Meets California Fire Standard 117.

Cleaning: Mild Soap and Water.

Chair Warranty

PRINT

Seating Products Warranty

- Frames are warranted to stay as strong as when they were new for 10 years.

- Upholstery, including the foam, fabric and molded wood understructure must remain attractive and in proper working condition for five years. (The exception shall be damage due to customer impacts, burns, stains, cuts, etc.)

- Our bumper-grade chrome will not delaminate, fade, rust or become unattractive for 10 - years.

- Static Control (ESD) properties of our seating must remain within the nationally accepted standards of ANSI/ESDA S20.20, GSA and The ESD Association established and in place at the time of sale, for 10 - years.

- Clean room seating must maintain the standards of a Class 100 for 10 - years.

Exceptions: Our seating warranty is extended to the original purchaser and is prorated when the chairs are used in multiple-shift operations.

BenchPro™ will refund the entire purchase price including freight and tax (if any) or replace the product or component that is defective, and pay for the freight.

Due Diligence: Please, if a chair is found to be defective in a way that could lead to an accident, take it out of service and tag it as dangerous until replacements or replacement parts are received and assembled.

Destruction: Dangerous products should not be put into open waste disposal system until they have been made unusable, so no third party can claim them and be injured.

Product Returns:

1. No return is ever required. (We may ask for an electronic photo in cases where we have not seen the problem before).

2. If the product is purchased but not needed, and returned with freight prepaid, and in new condition with original packing materials, we charge a restocking charge. We also charge a restocking charge for products ordered but cancelled after the product is built. (This is to cover our repackaging, reselling and handling).

From the lawyers: In no case shall BenchPro™, its distributors, employees, related divisions, and other entities be responsible for any direct, consequential or indirect damage caused by the use, inability to use, or incorrect use of our products. Our liability is limited to replacement of product or a full refund.

Ease of Assembly

Tall Chairs Assembly Instructions

3 LEVER CONTROL

Assembly Below

1. No tools are required. Unpack the box. Insert the casters into the base. Turn the base over.

2. After inserting the gas cylinder into the base, slide the footring up the gas cylinder and secure the footring.

3. Place the cushion and steel plate over the top of the gas cylinder.

4. Remove the knob on the back. Reinsert the knob. Tighten.

5. Remove the knob on the bottom of the seat plate. Reinsert the knob and washers. Tighten.

1 LEVER CONTROL

Assembly Below

1. No tools are required. Unpack the box. Insert the casters into the base. Turn the base over.

2. After inserting the gas cylinder into the base, slide the footring up the gas cylinder and secure the footring.

3. Place the cushion and steel plate over the top of the gas cylinder.

4. Insert back bar through the steel plate and adjust the back bar at desired height. Tighten.

5. Insert the plastic pin onto the back bar.

Accessories

	Arms Add Fixed, Adjustable or ESD Arms.
	Casters Add Braking, Urethane or Glides.
	Bin Box Holder Keep Small Parts Close to You.
	Bottle Holder Convenient Bottle Handling.
	Tool Holder Accommodates any Tool.